FS-3830

Kyocera FS-3830 printer

The Kyocera FS-3830 is the step-up monochrome laser printer for offices that have started to outgrow the FS-3820: same compact footprint on the desk, noticeably more headroom for daily volume. It feeds from the TK67 black toner cartridges stocked on this page — the designation under which this engine's long-life cartridge is listed here. Kyocera documents that cartridge for this engine as the TK-65, rated at up to 20,000 pages per ISO/IEC 19752, and it is a toner-only design: the drum is a separate long-life unit, so a refill means swapping toner and nothing else.

Pick the FS-3830 when a shared workgroup printer has begun to form queues at month-end — invoice runs, report packs and statement batches that made the smaller machine feel tight. It suits a busy team that prints all day but has no room, and no need, for a full departmental system. Because the toner platform carries over from the 3820 generation, staff already know the cartridge routine; only the pace changes. One black cartridge, a drum that stays in the machine for the long haul, and output that keeps up with a growing office.

Toner Cartridges for FS-3830

Cartridge	Color	Page Yield
TK67 — Single Cartridge	Black	See product page
TK67 — 2 Pack	Black	See product page
TK67 — 3 Pack	Black	See product page
TK67 — 5 Pack	Black	See product page
TK67 — 10 Pack	Black	See product page

Which cartridge should you buy?

Start with how the machine is actually used. A single cartridge suits a lightly used FS-3830, but most of these printers are shared, and a shared printer that stops for toner stops everyone. The cartridge family for this engine is rated at up to 20,000 pages, so changes are rare events rather than weekly chores — which is exactly why a 2-pack or larger bundle makes sense: one cartridge in the machine, one on the shelf, and a reorder only when the spare goes in. Bigger bundles (3, 5 and 10 packs) suit offices standardizing several machines on the same cartridge, where the per-cartridge cost drops and the supply closet holds one SKU.

Chip, toner and everyday use

Swapping this cartridge is a toner-only job. The drum is a separate long-life unit that stays in the printer, so there is no drum counter to reset and nothing else to change at refill time. Slide the new cartridge in until it seats fully; if the printer does not recognize it at first, remove it, confirm the sealing tape is fully pulled, and reseat it firmly. Near the end of a cartridge, a gentle side-to-side shake redistributes the remaining toner and often recovers a few hundred even pages. Keep the spare stored flat, sealed, and away from heat and direct sunlight.

Frequently Asked Questions

Which toner does the FS-3830 take?

It runs on the long-life black toner documented for this engine as the TK-65; the compatible cartridges stocked on this page carry the TK67 designation. One cartridge design covers the whole 3820/3830 generation, in single and multi-pack listings.

Does the FS-3830 need its drum replaced with the toner?

No. The drum is a separate long-life unit, and the cartridge is toner-only. You replace just the toner when it runs low; the drum stays in the machine far beyond a single cartridge's life.

Does the same cartridge fit the FS-3830N?

Yes. The FS-3830N shares this print engine and takes the same cartridge, so one stock of toner covers both the standard and network versions.

How many pages should I expect from a cartridge?

The rating for this engine's cartridge is up to 20,000 pages, measured per ISO/IEC 19752 at about 5% page coverage. Dense pages — forms with heavy blocks of text, graphics, solid fills — use toner faster, so real-world life lands below the rating in most busy offices.