Xpress M2670

The Xpress M2670 sits a half-step above the base of its mono line — a slightly quicker engine for small offices that want more pace without moving up a full class. It stays on the D115 side of the family split, running one-piece cartridges that combine toner and drum in a single unit: a standard size, or the high-yield MLT-D115L with a 3,000-page rating, which is the cartridge this page stocks in singles and multipacks.
Mid-range machines like this one are bought on a calculation: enough speed for a small team's daily documents, without workgroup pricing. The running-cost half of that calculation is decided at the supply shelf. A compatible high-yield cartridge keeps the per-page figure where the M2670's positioning promises it will be, and the one-piece design keeps maintenance to a single swap — no drum orders, no second part number to remember, nothing to stock twice.
Toner Cartridges for Xpress M2670
| Cartridge | Color | Page Yield |
|---|---|---|
| MLT-D115L | Black | 3,000 pages |
| MLT-D115L 3 Pack | Black | 3,000 pages per cartridge |
| Xpress M2670 High Yield | Black | 3,000 pages |
| MLT-D115L Premium Quality 5 Pack | Black | 3,000 pages per cartridge |
| Xpress M2670 High Yield 5 Pack | Black | 3,000 pages per cartridge |
The standard-yield MLT-D115S from the same family also fits this printer; the listings above focus on the high-yield L, including the cartridge named for the M2670 and a premium-grade 5 pack for offices that standardize on it.
Which cartridge should you buy?
Choose by rhythm. A small office printing every day belongs on the MLT-D115L: 3,000 pages per fill, the lowest cost per page in the family, and fewer interruptions across the year. The standard MLT-D115S is the honest alternative for a printer that only stirs a few times a month — toner does not improve with age, so capacity you will not use within a year or so buys nothing. Teams that cannot afford a mid-job stop should move up to the 3 pack or a 5 pack, which lowers the per-cartridge price and guarantees the replacement is already in the building when the gauge runs out.
Chip, toner and everyday use
The M2670 reads the cartridge's chip to follow toner level, so a new MLT-D115L registers full on installation. Treat the 3,000-page figure as a 5%-coverage estimate: dense documents finish fills faster, sparse ones stretch them further. Near the end of a cartridge, a gentle side-to-side rock redistributes the remaining toner and usually restores even density for a while. Every cartridge change also renews the built-in drum, which is why this family has no separate drum to order. Store spares in their sealed bags, flat and away from sunlight, and rotate stock so the oldest cartridge goes in first.
Frequently Asked Questions
MLT-D115S or MLT-D115L for the M2670 — which one?
The two cartridges fit the same slot. The L carries the 3,000-page high-yield fill and the better per-page cost, suiting a printer in daily service; the S is the lower-priced standard fill for light, occasional use.
A listing offers me MLT-D116L for this printer. Should I take it?
No. The D116 belongs to the neighboring branch of the family and does not fit the M2670, however close the names look. This printer's cartridges are the D115 line — verify the full code before ordering.
Prints from my M2670 look faded. Toner or something else?
Rule out settings first: toner-save or draft mode left switched on will wash out every page. Then rock the cartridge gently to level its fill. If density stays weak after both checks, the cartridge is genuinely near its end.
Is there a drum I need to replace separately?
There is not. Toner and drum are one unit in the D115 design, so the MLT-D115L you install already contains a fresh drum — one part number covers the whole supply cycle.
